A garbage disposal that's been making grinding sounds for months before stopping entirely often has a seized bearing or cracked impeller โ signs the motor isn't worth repairing. Our techs in Fulton tell you honestly whether a repair or a same-day unit swap makes more financial sense.
๐ Call +1-855-718-1500 โ Same-Day Service
Garbage disposal failures have specific, diagnosable causes. Our techs don't just swap units โ they identify what failed and whether repair or replacement is the right call for your situation.
Hum but no spin: jammed impeller. No sound at all: tripped thermal overload or failed motor. Intermittent operation: loose wiring at the switch or disposal unit. Continuous drain from the sink collar: failed sink flange gasket. Leak from the side: dishwasher drain hose connection or internal body crack. We trace the symptom to the specific cause before recommending any solution.
InSinkErator models use a 1/4-inch Allen wrench at the center bottom; Waste King models use a broom-handle approach at the top. Knowing which you have before arriving saves time and prevents the wrong tool damaging the motor shaft.
We give you the actual cost comparison. If clearing the jam and pressing the reset button fixes it, that's what we do. If the motor has failed, we show you the replacement options and install same-day.
A disposal isn't an isolated appliance โ it connects to the sink drain, the dishwasher drain (if present), and the drain arm leading to the p-trap. We inspect the full connection set during any disposal call: drain arm slope, dishwasher drain knockout (if a dishwasher is being added), and p-trap connection integrity.
Most disposal calls complete in 30โ60 minutes โ same visit, flat-rate pricing.
If the jam-clearing wrench won't budge the impeller, the motor shaft may be seized rather than just stuck from debris โ we distinguish between the two before recommending replacement.
If power is confirmed at the disposal and it still won't start after a reset, the motor is failed. We then move to the replacement conversation with honest cost comparison.
Disposal leaks come from three locations: the sink flange (top of the unit where it mounts to the sink drain opening โ repaired by re-sealing the flange with plumber's putty and re-tightening the mounting ring), the side port (dishwasher drain hose connection โ usually a loose hose clamp or cracked fitting), or the bottom of the unit (internal body crack or failed internal seal โ indicates replacement needed).
If the turntable bearing has failed โ indicated by a loud rumbling throughout operation rather than specific impact sounds โ that's an internal motor wear failure that warrants replacement.
If the slow drain persists after cleaning the drain arm and p-trap, a camera scope of the kitchen drain line is the next step to check for blockage further downstream.
When the motor has failed, the unit body is cracked, or the existing unit is underpowered for the household's use pattern, we replace the disposal with a new unit matched to the sink drain configuration. We carry 1/2 HP, 3/4 HP, and 1 HP units from InSinkErator and other major brands on our trucks for same-day installation.
A disposal call takes 30โ60 minutes in most cases. Here's exactly how it goes โ from your first call to a clean, functional kitchen drain.
If you know the disposal is over 10 years old, tell us โ that changes how we approach the repair-vs-replace conversation upfront.
For leaks, we dry the area completely and run a short test cycle to confirm exactly which connection is dripping.
You decide. We don't upsell replacement when repair is the right answer, and we don't push a cheap repair that won't hold on a unit that's genuinely at end of life.
We leave the cabinet dry and the disposal running quietly. If a dishwasher drain hose was involved, we run a dishwasher cycle to verify no backup occurs.

Disposal hummed and wouldn't spin. I'd already tried the Allen wrench trick without success. Masters Plumbing Service's tech came out, worked the impeller free from underneath while removing a piece of broken ceramic that had fallen in โ it had wedged between the impeller and the grinding ring in a way I couldn't have cleared from the top. Cleared the jam, pressed the reset, tested. Five-minute fix. Honest about the call minimum charge, no attempt to upsell a replacement on a perfectly good motor.
After we added a dishwasher, it started backing up every cycle. Masters Plumbing Service found the problem immediately โ the previous installer had forgotten to knock out the dishwasher drain plug inside the disposal inlet. The plug was blocking the drain port. Two-minute fix. The tech also tightened the dishwasher drain hose clamp, which was loose. Never had another backup.
Disposal leaking from the sink collar area. Previous owner had installed it with silicone instead of plumber's putty at the flange โ silicone doesn't hold the mounting pressure correctly and had separated. Tech re-seated the flange with putty, re-tightened the mounting ring, and the leak stopped. Tested with a full minute of running water. All clear.

Masters Plumbing Service dispatches garbage disposal repair and replacement technicians throughout Fulton and the broader Fulton, CA service area. Most calls are same-day โ call to check today's availability.

Call now โ same-day service available in Fulton and across Fulton, CA.
๐ Call +1-855-718-1500 Now